Ich verkaufe mein absturzfreies Black Vortex Board. Mit dabei ist noch ein Ultraschall Sensor und APC220 für Telemetrie. Ich kommt mit Arducopter einfach nicht klar und fliege das Board mit MultiWii und das ist einfach overkill. Daher verkauf ich es jetzt. Derzeit ist die MultiWII drauf aber ihr könnt es gerne mit der Megapirate/Arducopter Software haben.
Preis: 190Euro Komplett inkl. Versand. Die Teile werden nicht einzeln verkauft. paypal oder Überweisung
Noch ein paar Daten:
Die Löcher sich 45x45mm und sind auf M3 erweitert.
SENSORS:
HMC5883L Triple Axis Magnetometer
BMA180 Triple Axis Accelerometer
BMP085 Barometric Pressure Sensor
ITG3200 Triple-Axis Digital-Output Gyro
NEO-6Q Ublox GPS receiver
Atmega2560 16MHz 5V
LED:
3 pcs Status led A,B,C RED, Yellow, Green
2 pcs Tx Rx status LED for FTDI USB
2 pcs LED for 3.3V 5V power status
CONNECTORS:
8 pcs 3 pin connectors for servo or motor ESC
2 pcs 3 pin connectors for Pan Tilt servo
8 pcs 3 pin connectors for 8Ch RC receiver
1 pcs for sonar (two type avail)
1 pcs for xbee or other wireless modules
1 pcs LIGHT switch up to 8A for LED or other lights
5 pcs ANALOG input for external components
2 pcs 3.3V 500mA for external components
2 pcs 5.0V 500mA for external components
1 pcs for GPS antenna
1 pcs I2C and UART interface for external board
1 pcs ISP connector for Atmega2560 programming
1 USB based on FTDI chip. Arduino software compatible
Onboard 500mA 5V voltage regulator for external components
Onboard 500mA 3.3V voltage regulator for external components
Low noise LDO voltage regulator for all sensors and GPS
Preis: 190Euro Komplett inkl. Versand. Die Teile werden nicht einzeln verkauft. paypal oder Überweisung
Noch ein paar Daten:
Die Löcher sich 45x45mm und sind auf M3 erweitert.
SENSORS:
HMC5883L Triple Axis Magnetometer
BMA180 Triple Axis Accelerometer
BMP085 Barometric Pressure Sensor
ITG3200 Triple-Axis Digital-Output Gyro
NEO-6Q Ublox GPS receiver
Atmega2560 16MHz 5V
LED:
3 pcs Status led A,B,C RED, Yellow, Green
2 pcs Tx Rx status LED for FTDI USB
2 pcs LED for 3.3V 5V power status
CONNECTORS:
8 pcs 3 pin connectors for servo or motor ESC
2 pcs 3 pin connectors for Pan Tilt servo
8 pcs 3 pin connectors for 8Ch RC receiver
1 pcs for sonar (two type avail)
1 pcs for xbee or other wireless modules
1 pcs LIGHT switch up to 8A for LED or other lights
5 pcs ANALOG input for external components
2 pcs 3.3V 500mA for external components
2 pcs 5.0V 500mA for external components
1 pcs for GPS antenna
1 pcs I2C and UART interface for external board
1 pcs ISP connector for Atmega2560 programming
1 USB based on FTDI chip. Arduino software compatible
Onboard 500mA 5V voltage regulator for external components
Onboard 500mA 3.3V voltage regulator for external components
Low noise LDO voltage regulator for all sensors and GPS
Anhänge
-
1,5 MB Aufrufe: 23